Exhaust Waterlocks and Mufflers

Exhaust Waterlocks and Mufflers

Exhaust Waterlocks and Mufflers

Show:
Sort By:

Exhaust Waterlock Vetus MGL84510A (203mm In / 250mm Out / 130 Litres)

Exhaust Waterlock Vetus MGL84510A (203mm In / 250mm Out / 130 Litres) The Vetus MGL84510A is a marine exhaust waterlock made from synthetic materials. The MG range of waterlocks are particularly designed for larger boats and high performance craft. Due to the design of the waterlock, it also acts as an exhaust sound muffler. Vetus MGL waterlocks feature dual stage functionality, consisting of one lower chamber and one upper chamber. Coolant water and exhaust gas enter the inlet in the bottom chamber, travel up through the central riser tube and then exit through the outlet in the top chamber. The design prevents water flowing back down the exhaust line to the engine when it is switched off. Installation of the Vetus waterlock is easy and flexible, due to the compact and clever design. The upper chamber can rotate through 360° to correctly position inlet and outlet ports to suit your application. The inlet port i..

(7)

1,217.83€ Ex Tax: 1,217.83€

Centek GRP Exhaust Waterlock (Side Angle In - Top Out / 152mm Hose)

Centek GRP Exhaust Waterlock (Side Angle In - Top Out / 152mm Hose) The Centek 1500117 Vernalift waterlock features a 'Side Angle In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet ex..

(5)

1,001.16€ Ex Tax: 1,001.16€

Centek Vernatone Round GRP Exhaust Muffler (152mm Hose)

Centek Vernatone Round GRP Exhaust Muffler (152mm Hose) The Centek 1000111 inline Vernatone Round muffler is suitable for all inboard engines. The Vernatone is suitable for use with petrol (gas) or diesel but must only be installed above the waterline. It has good sound absorbing properties of 15-18 dB depending on the engine it is being used with. The Centek range of exhaust mufflers are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the mufflers are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernatone is only suitable for use in wet exhaust systems and should be used with approved rubber marine exhaust hose. Specifications Application Inboards ..

(6)

987.77€ Ex Tax: 987.77€

Centek GRP Exhaust Waterlock (Side In - Top Out / 152mm Hose)

Centek GRP Exhaust Waterlock (Side In - Top Out / 152mm Hose) The Centek 1500092 Vernalift waterlock features a 'Side In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaust system..

(9)

931.21€ Ex Tax: 931.21€

Centek Vernatone Round MKII GRP Exhaust Muffler (127mm Hose)

Centek Vernatone Round MKII GRP Exhaust Muffler (127mm Hose) The Centek 1400006 Vernatone Round muffler is suitable for all inboard engines. The Vernatone is suitable for use with petrol (gas) or diesel but must only be installed above the waterline. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. This is a MKII version of the Vernatone Round. It features a better sound rating and has slightly offset ports, with the outlet above the inlet. The Centek range of exhaust mufflers are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the mufflers are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernatone is only suitable for use in wet exhaust systems and should be used with appro..

(13)

859.78€ Ex Tax: 859.78€

Centek GRP Exhaust Waterlock (Side In - Top Out / 127mm Hose)

Centek GRP Exhaust Waterlock (Side In - Top Out / 127mm Hose) The Centek 1500090 Vernalift waterlock features a 'Side In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaust system..

(10)

805.46€ Ex Tax: 805.46€

Centek Vernatone Round GRP Exhaust Muffler (127mm Hose)

Centek Vernatone Round GRP Exhaust Muffler (127mm Hose) The Centek 1000108 inline Vernatone Round muffler is suitable for all inboard engines. The Vernatone is suitable for use with petrol (gas) or diesel but must only be installed above the waterline. It has good sound absorbing properties of 15-18 dB depending on the engine it is being used with. The Centek range of exhaust mufflers are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the mufflers are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernatone is only suitable for use in wet exhaust systems and should be used with approved rubber marine exhaust hose. Specifications Application Inboards ..

(12)

742.62€ Ex Tax: 742.62€

Centek GRP Exhaust Waterlock (64mm Side Angle In, 76mm Top Out)

Centek GRP Exhaust Waterlock (64mm Side Angle In, 76mm Top Out) The Centek 1500160 Vernalift waterlock features a 'Side Angle In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaus..

(14)

665.88€ Ex Tax: 665.88€

Gas/Water Separator Centek Gen-Sep (76mm Exhaust / 38mm Water Drain)

Gas/Water Separator Centek Gen-Sep (76mm Exhaust / 38mm Water Drain) Centek 1020301 Gen-Sep separator designed to separate exhaust gases and coolant water in a marine wet exhaust system, before discarding the water below the waterline to eliminate splash. The separator also acts as an exhaust muffler while routing all the exhaust gas and cooling water overboard separately. Centek Gen-Sep units are made from the same GRP materials used in all Centek wet exhaust system components. This gas/water separator is designed for use with diesel engines, particularly useful for those located amidships or well forward in the hull. All ports are situated on the bottom of the unit, with two interchangeable ports for the inlet and outlet of exhaust gases and one central outlet for water drain. Specifications Height 521mm ..

(15)

663.43€ Ex Tax: 663.43€

Exhaust Waterlock Centek Vernalift GRP (Inline / 127mm Hose)

Exhaust Waterlock Centek Vernalift GRP (Inline / 127mm Hose) The Centek 1500100 Vernalift waterlock features an 'Inline' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaust systems and shoul..

(15)

606.67€ Ex Tax: 606.67€

Vetus Linear Muffler for 150mm Hose

Vetus Linear Muffler for 150mm HoseVetus Muffler MV150 150mm. Muffler for big engines and for speed boats with reduced available space. Specially developed for fast craft with powerful engines, where very often there is no space available for installation of a Waterlock and/or gooseneck. Application in combination with water-injected exhaust systems only. All parts are made of synthetic materials (no corrosion). Tremendous reduction of exhaust noise. Back pressure is absolutely minimal. Compact dimensions and light-weight. Stainless steel mounting brackets for the muffler are standard supply. The transom connection can be stainless steel (model TRC125VS), or reinforced black plastic, with a stainless steel band (model TC125). Both types are provided with a check valve. For muffler model MV a temperature sensor for a raw water alarm is optional and can be supplied with the muffler. The muffler and the transom connection of this exhaust system may only be installed when the transom con..

(12)

603.35€ Ex Tax: 603.35€

Exhaust Muffler Centek Vernatone Round MKII GRP (102mm Hose)

Exhaust Muffler Centek Vernatone Round MKII GRP (102mm Hose) The Centek 1400017 Vernatone Round muffler is suitable for all inboard engines. The Vernatone is suitable for use with petrol (gas) or diesel but must only be installed above the waterline. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. This is a MKII version of the Vernatone Round. It features a better sound rating and has slightly offset ports, with the outlet above the inlet. The Centek range of exhaust mufflers are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the mufflers are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernatone is only suitable for use in wet exhaust systems and should be used with appro..

(5)

599.46€ Ex Tax: 599.46€

Water Separator Centek Gen-Sep (51mm Exhaust / 38mm Water)

Water Separator Centek Gen-Sep (51mm Exhaust / 38mm Water) Centek 1020200 Gen-Sep separator designed to separate exhaust gases and coolant water in a marine wet exhaust system, before discarding the water below the waterline to eliminate splash. The separator also acts as an exhaust muffler while routing all the exhaust gas and cooling water overboard separately. Centek Gen-Sep units are made from the same GRP materials used in all Centek wet exhaust system components. This gas/water separator is designed for use with diesel engines, particularly useful for those located amidships or well forward in the hull. All ports are situated on the bottom of the unit, with two interchangeable ports for the inlet and outlet of exhaust gases and one central outlet for water drain. Specifications Height 397mm W..

(3)

587.71€ Ex Tax: 587.71€

Exhaust Waterlock Muffler Vetus MGP 127mm

Exhaust Waterlock Muffler Vetus MGP 127mmWaterlock for water injected exhaust systems, with rotatable top. Made of corrosion-free synthetic materials. Excellent sound reduction. Often in a modern high performance boat, with one or two large engines installed, there is very little space to spare in the engine room. VETUS waterlocks, model MG are designed to make even the most awkward installation possible. The outlet connection at the top will rotate through 360° and the inlet connection is at an angle of 45° upward. Models with horizontal inlet connection, or angled 15° or 30°, are available to special order, minimum quantity of 10 units per order. VETUS waterlocks, type MG, may only be installed in water injected exhaust systems. They are made entirely of synthetic materials (no corrosion or galvanic action), have excellent sound reduction properties and cause minimal back pressure. The clamp bands are made of stainless steel. Provided with a drain cock for winter storage...

(4)

583.86€ Ex Tax: 583.86€

Exhaust Waterlock Muffler Vetus MGP 102mm

Exhaust Waterlock Muffler Vetus MGP 102mmWaterlock for water injected exhaust systems, with rotatable top. Made of corrosion-free synthetic materials. Excellent sound reduction. Often in a modern high performance boat, with one or two large engines installed, there is very little space to spare in the engine room. VETUS waterlocks, model MG are designed to make even the most awkward installation possible. The outlet connection at the top will rotate through 360° and the inlet connection is at an angle of 45° upward. Models with horizontal inlet connection, or angled 15° or 30°, are available to special order, minimum quantity of 10 units per order. VETUS waterlocks, type MG, may only be installed in water injected exhaust systems. They are made entirely of synthetic materials (no corrosion or galvanic action), have excellent sound reduction properties and cause minimal back pressure. The clamp bands are made of stainless steel. Provided with a drain cock for winter storage...

(11)

573.25€ Ex Tax: 573.25€

Vetus Linear Muffler for 125mm Hose

Vetus Linear Muffler for 125mm HoseVetus Muffler MV125 125mm. Muffler for big engines and for speed boats with reduced available space. Specially developed for fast craft with powerful engines, where very often there is no space available for installation of a Waterlock and/or gooseneck. Application in combination with water-injected exhaust systems only. All parts are made of synthetic materials (no corrosion). Tremendous reduction of exhaust noise. Back pressure is absolutely minimal. Compact dimensions and light-weight. Stainless steel mounting brackets for the muffler are standard supply. The transom connection can be stainless steel (model TRC125VS), or reinforced black plastic, with a stainless steel band (model TC125). Both types are provided with a check valve. For muffler model MV a temperature sensor for a raw water alarm is optional and can be supplied with the muffler. The muffler and the transom connection of this exhaust system may only be installed when the transom con..

(5)

572.22€ Ex Tax: 572.22€

Water Separator Centek Gen-Sep (41mm Exhaust / 32mm Water)

Water Separator Centek Gen-Sep (41mm Exhaust / 32mm Water) Centek 1020162 Gen-Sep separator designed to separate exhaust gases and coolant water in a marine wet exhaust system, before discarding the water below the waterline to eliminate splash. The separator also acts as an exhaust muffler while routing all the exhaust gas and cooling water overboard separately. Centek Gen-Sep units are made from the same GRP materials used in all Centek wet exhaust system components. This gas/water separator is designed for use with diesel engines, particularly useful for those located amidships or well forward in the hull. All ports are situated on the bottom of the unit, with two interchangeable ports for the inlet and outlet of exhaust gases and one central outlet for water drain. Specifications Height 397mm Wi..

(15)

570.31€ Ex Tax: 570.31€

Centek Low Capacity GRP Exhaust Waterlock (Side In - Top Out / 127mm)

Centek Low Capacity GRP Exhaust Waterlock (Side In - Top Out / 127mm) The Centek 1500091 Vernalift waterlock features a 'Side In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaus..

(9)

566.40€ Ex Tax: 566.40€

Exhaust Waterlock Muffler Vetus MGP 90mm

Exhaust Waterlock Muffler Vetus MGP 90mmWaterlock for water injected exhaust systems, with rotatable top. Made of corrosion-free synthetic materials. Excellent sound reduction. Often in a modern high performance boat, with one or two large engines installed, there is very little space to spare in the engine room. VETUS waterlocks, model MG are designed to make even the most awkward installation possible. The outlet connection at the top will rotate through 360° and the inlet connection is at an angle of 45° upward. Models with horizontal inlet connection, or angled 15° or 30°, are available to special order, minimum quantity of 10 units per order. VETUS waterlocks, type MG, may only be installed in water injected exhaust systems. They are made entirely of synthetic materials (no corrosion or galvanic action), have excellent sound reduction properties and cause minimal back pressure. The clamp bands are made of stainless steel. Provided with a drain cock for winter storage. Capacity:..

(9)

563.67€ Ex Tax: 563.67€

Water Separator Centek Gen-Sep (38mm Exhaust / 32mm Water)

Water Separator Centek Gen-Sep (38mm Exhaust / 32mm Water) Centek 1020150 Gen-Sep separator designed to separate exhaust gases and coolant water in a marine wet exhaust system, before discarding the water below the waterline to eliminate splash. The separator also acts as an exhaust muffler while routing all the exhaust gas and cooling water overboard separately. Centek Gen-Sep units are made from the same GRP materials used in all Centek wet exhaust system components. This gas/water separator is designed for use with diesel engines, particularly useful for those located amidships or well forward in the hull. All ports are situated on the bottom of the unit, with two interchangeable ports for the inlet and outlet of exhaust gases and one central outlet for water drain. Specifications Height 397mm Wi..

(3)

562.96€ Ex Tax: 562.96€

Exhaust Waterlock 102mm Centek GRP

Exhaust Waterlock 102mm Centek GRP The Centek 1500114 Vernalift waterlock features a 'Side Angle In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaust systems and should be used ..

(8)

559.77€ Ex Tax: 559.77€

Vetus Exhaust Gas and Water Separator (75mm Exhaust, 50mm Water Drain)

Vetus Exhaust Gas and Water Separator (75mm Exhaust, 50mm Water Drain) This plastic Vetus exhaust gas separator is designed to separate the exhaust gas from the injected raw cooling water in a marine exhaust system. It also performs all the functions of a gooseneck as well as helping to muffle the noise within the exhaust system. A stainless steel mounting strap with synthetic straps is also supplied to secure the exhaust gas separator. The inlet and outlet exhaust hose connectors also rotate through 360° to allow flexibility in installation. Vetus exhaust components are made from plastic and must only be fitted into wet exhaust systems. Maximum temperature should not exceed 70°C, otherwise the exhaust components may be damaged. Specifications Capacity 12 Litres Height ..

(13)

553.61€ Ex Tax: 553.61€

Vetus Exhaust Gas and Water Separator (60mm Exhaust, 50mm Water Drain)

Vetus Exhaust Gas and Water Separator (60mm Exhaust, 50mm Water Drain) This plastic Vetus exhaust gas separator is designed to separate the exhaust gas from the injected raw cooling water in a marine exhaust system. It also performs all the functions of a gooseneck as well as helping to muffle the noise within the exhaust system. A stainless steel mounting strap with synthetic straps is also supplied to secure the exhaust gas separator. The inlet and outlet exhaust hose connectors also rotate through 360° to allow flexibility in installation. Vetus exhaust components are made from plastic and must only be fitted into wet exhaust systems. Maximum temperature should not exceed 70°C, otherwise the exhaust components may be damaged. Specifications Capacity 12 Litres Height ..

(14)

551.81€ Ex Tax: 551.81€

Centek Vernatone Round GRP Exhaust Muffler (102mm Hose)

Centek Vernatone Round GRP Exhaust Muffler (102mm Hose) The Centek 1000106 inline Vernatone Round muffler is suitable for all inboard engines. The Vernatone is suitable for use with petrol (gas) or diesel but must only be installed above the waterline. It has good sound absorbing properties of 15-18 dB depending on the engine it is being used with. The Centek range of exhaust mufflers are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the mufflers are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernatone is only suitable for use in wet exhaust systems and should be used with approved rubber marine exhaust hose. Specifications Application Inboards ..

(6)

516.74€ Ex Tax: 516.74€

Centek Vernalift GRP Exhaust Waterlock (Side In, Top Out / 102mm Hose)

Centek Vernalift GRP Exhaust Waterlock (Side In, Top Out / 102mm Hose) The Centek 1500088 Vernalift waterlock features a 'Side In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhau..

(8)

510.88€ Ex Tax: 510.88€

Centek Vernalift GRP Exhaust Waterlock (Side In - Top Out / 89mm Hose)

Centek Vernalift GRP Exhaust Waterlock (Side In - Top Out / 89mm Hose) The Centek 1500087 Vernalift waterlock features a 'Side In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhau..

(8)

497.49€ Ex Tax: 497.49€

Centek MiniMax GRP Exhaust Muffler (127mm Hose)

Centek MiniMax GRP Exhaust Muffler (127mm Hose) The Centek 1050500 inline MiniMax muffler is designed primarily for V-drives and locations which are short on space. The MiniMax is suitable for use with petrol (gas) or diesel but must only be installed above the waterline. It has fair sound absorbing properties of 10-12 dB depending on the engine it is being used with. The Centek range of exhaust mufflers are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the mufflers are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek MiniMax is only suitable for use in wet exhaust systems and should be used with approved rubber marine exhaust hose. Specifications Application ..

(3)

493.37€ Ex Tax: 493.37€

Inline Exhaust Muffler Vetus MP D150

Inline Exhaust Muffler Vetus MP D150Muffler for big engines...

(12)

490.50€ Ex Tax: 490.50€

Inline Exhaust Muffler Vetus MP D125

Inline Exhaust Muffler Vetus MP D125Muffler for big engines...

(15)

489.00€ Ex Tax: 489.00€

Centek GRP Exhaust Waterlock (Side Angle In - Top Out / 76mm Hose)

Centek GRP Exhaust Waterlock (Side Angle In - Top Out / 76mm Hose) The Centek 1500112 Vernalift waterlock features a 'Side Angle In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exh..

(6)

481.01€ Ex Tax: 481.01€

Vetus Exhaust Gas and Water Separator (50mm Exhaust, 38mm Water Drain)

Vetus Exhaust Gas and Water Separator (50mm Exhaust, 38mm Water Drain) This plastic Vetus exhaust gas separator is designed to separate the exhaust gas from the injected raw cooling water in a marine exhaust system. It also performs all the functions of a gooseneck as well as helping to muffle the noise within the exhaust system. A stainless steel mounting strap with synthetic straps is also supplied to secure the exhaust gas separator. The inlet and outlet exhaust hose connectors also rotate through 360° to allow flexibility in installation. Vetus exhaust components are made from plastic and must only be fitted into wet exhaust systems. Maximum temperature should not exceed 70°C, otherwise the exhaust components may be damaged. Specifications Capacity 7 Litres Height ..

(5)

474.23€ Ex Tax: 474.23€

Exhaust Waterlock Centek Vernalift GRP (Inline / 64mm Hose)

Exhaust Waterlock Centek Vernalift GRP (Inline / 64mm Hose) The Centek 1500049 Vernalift waterlock features an 'Inline' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaust systems and should..

(13)

473.52€ Ex Tax: 473.52€

Vetus Exhaust Gas and Water Separator (45mm Exhaust, 38mm Water Drain)

Vetus Exhaust Gas and Water Separator (45mm Exhaust, 38mm Water Drain) This plastic Vetus exhaust gas separator is designed to separate the exhaust gas from the injected raw cooling water in a marine exhaust system. It also performs all the functions of a gooseneck as well as helping to muffle the noise within the exhaust system. A stainless steel mounting strap with synthetic straps is also supplied to secure the exhaust gas separator. The inlet and outlet exhaust hose connectors also rotate through 360° to allow flexibility in installation. Vetus exhaust components are made from plastic and must only be fitted into wet exhaust systems. Maximum temperature should not exceed 70°C, otherwise the exhaust components may be damaged. Specifications Capacity 7 Litres Height ..

(11)

463.37€ Ex Tax: 463.37€

Vetus Exhaust Gas and Water Separator (40mm Exhaust, 38mm Water Drain)

Vetus Exhaust Gas and Water Separator (40mm Exhaust, 38mm Water Drain) This plastic Vetus exhaust gas separator is designed to separate the exhaust gas from the injected raw cooling water in a marine exhaust system. It also performs all the functions of a gooseneck as well as helping to muffle the noise within the exhaust system. A stainless steel mounting strap with synthetic straps is also supplied to secure the exhaust gas separator. The inlet and outlet exhaust hose connectors also rotate through 360° to allow flexibility in installation. Vetus exhaust components are made from plastic and must only be fitted into wet exhaust systems. Maximum temperature should not exceed 70°C, otherwise the exhaust components may be damaged. Specifications Capacity 7 Litres Height ..

(6)

452.52€ Ex Tax: 452.52€

Linear Exhaust Muffler Vetus MV 100

Linear Exhaust Muffler Vetus MV 100Muffler for big engines and for speed boats with reduced available space...

(15)

440.38€ Ex Tax: 440.38€

Linear Exhaust Muffler Vetus MV 90

Linear Exhaust Muffler Vetus MV 90Muffler for big engines and for speed boats with reduced available space...

(3)

429.07€ Ex Tax: 429.07€

Centek Low Capacity GRP Inline Exhaust Waterlock (60mm Hose)

Centek Low Capacity GRP Inline Exhaust Waterlock (60mm Hose) The Centek 1500047 Vernalift waterlock features an 'Inline' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaust systems and shoul..

(15)

422.25€ Ex Tax: 422.25€

Exhaust Waterlock Vetus LSG 90

Exhaust Waterlock Vetus LSG 90Extra large waterlock for boats sailing in rough waters. Capacity 17 liters with no return valve and rotating inlet/outlet for easy installation...

(7)

419.56€ Ex Tax: 419.56€

Centek Vernalift GRP Exhaust Waterlock (51mm Hose / Inline)

Centek Vernalift GRP Exhaust Waterlock (51mm Hose / Inline) The Centek 1500044 Vernalift waterlock features an 'Inline' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaust systems and should..

(8)

415.86€ Ex Tax: 415.86€

Exhaust Waterlock Vetus LSG 75

Exhaust Waterlock Vetus LSG 75Extra large waterlock for boats sailing in rough waters. Capacity 17 liters with no return valve and rotating inlet/outlet for easy installation...

(13)

410.97€ Ex Tax: 410.97€

Centek MiniMax GRP Exhaust Muffler (102mm Hose)

Centek MiniMax GRP Exhaust Muffler (102mm Hose) The Centek 1050400 inline MiniMax muffler is designed primarily for V-drives and locations which are short on space. The MiniMax is suitable for use with petrol (gas) or diesel but must only be installed above the waterline. It has fair sound absorbing properties of 10-12 dB depending on the engine it is being used with. The Centek range of exhaust mufflers are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the mufflers are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek MiniMax is only suitable for use in wet exhaust systems and should be used with approved rubber marine exhaust hose. Specifications Application ..

(11)

397.58€ Ex Tax: 397.58€

Exhaust Waterlock Vetus LSG 60

Exhaust Waterlock Vetus LSG 60Extra large waterlock for boats sailing in rough waters. Capacity 17 liters with no return valve and rotating inlet/outlet for easy installation...

(8)

396.55€ Ex Tax: 396.55€

Centek Vernatone Round MKII GRP Exhaust Muffler (76mm Hose)

Centek Vernatone Round MKII GRP Exhaust Muffler (76mm Hose) The Centek 1400015 Vernatone Round muffler is suitable for all inboard engines. The Vernatone is suitable for use with petrol (gas) or diesel but must only be installed above the waterline. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. This is a MKII version of the Vernatone Round. It features a better sound rating and has slightly offset ports, with the outlet above the inlet. The Centek range of exhaust mufflers are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the mufflers are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernatone is only suitable for use in wet exhaust systems and should be used with approv..

(6)

396.55€ Ex Tax: 396.55€

Vetus Exhaust Muffler inline 100mm

Vetus Exhaust Muffler inline 100mmMuffler for big engines. ..

(13)

393.91€ Ex Tax: 393.91€

Centek Low Capacity GRP Inline Exhaust Waterlock (44mm Hose)

Centek Low Capacity GRP Inline Exhaust Waterlock (44mm Hose) The Centek 1500038 Vernalift waterlock features an 'Inline' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaust systems and shoul..

(5)

389.72€ Ex Tax: 389.72€

Inline Exhaust Muffler Vetus MP 90

Inline Exhaust Muffler Vetus MP 90Muffler for big engines...

(11)

381.69€ Ex Tax: 381.69€

Centek GRP Exhaust Waterlock (Side In - Top Out / 76mm Hose)

Centek GRP Exhaust Waterlock (Side In - Top Out / 76mm Hose) The Centek 1500034 black Vernalift waterlock features a 'Side In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaust s..

(14)

378.60€ Ex Tax: 378.60€

Centek Vernalift GRP Exhaust Waterlock (Inline / 51mm Hose)

Centek Vernalift GRP Exhaust Waterlock (Inline / 51mm Hose) The Centek 1500043 Vernalift waterlock features an 'Inline' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaust systems and should..

(15)

375.06€ Ex Tax: 375.06€

Centek Vernalift GRP Exhaust Waterlock (Inline / 44mm Hose)

Centek Vernalift GRP Exhaust Waterlock (Inline / 44mm Hose) The Centek 1500039 Vernalift waterlock features an 'Inline' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaust systems and should..

(14)

371.51€ Ex Tax: 371.51€

Centek Low Capacity GRP Exhaust Waterlock (Top In - Top Out / 76mm)

Centek Low Capacity GRP Exhaust Waterlock (Top In - Top Out / 76mm) The Centek 1500017 Vernalift waterlock features a 'Top In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaust s..

(15)

371.51€ Ex Tax: 371.51€

Centek GRP Exhaust Waterlock (Side Angle In - Top Out / 61mm Hose)

Centek GRP Exhaust Waterlock (Side Angle In - Top Out / 61mm Hose) The Centek 1500122 Vernalift waterlock features a 'Side Angle In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exh..

(3)

365.72€ Ex Tax: 365.72€

Centek GRP Exhaust Waterlock (Side In - Top Out / 60mm Hose)

Centek GRP Exhaust Waterlock (Side In - Top Out / 60mm Hose) The Centek 1500031 Vernalift waterlock features a 'Side In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaust systems..

(12)

359.95€ Ex Tax: 359.95€

Centek GRP Exhaust Waterlock (Side Angle In - Top Out / 51mm Hose)

Centek GRP Exhaust Waterlock (Side Angle In - Top Out / 51mm Hose) The Centek 1500107 Vernalift waterlock features a 'Side Angle In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exh..

(10)

356.85€ Ex Tax: 356.85€

Centek Vernalift GRP Exhaust Waterlock (Side In - Top Out / 64mm Hose)

Centek Vernalift GRP Exhaust Waterlock (Side In - Top Out / 64mm Hose) The Centek 1500032 Vernalift waterlock features a 'Side In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhau..

(5)

354.16€ Ex Tax: 354.16€

Centek Low Capacity GRP Inline Exhaust Waterlock (51mm Hose)

Centek Low Capacity GRP Inline Exhaust Waterlock (51mm Hose) The Centek 1500042 Vernalift waterlock features an 'Inline' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaust systems and shoul..

(5)

354.16€ Ex Tax: 354.16€

Centek Vernalift GRP Exhaust Waterlock (Top In - Top Out / 60mm Hose)

Centek Vernalift GRP Exhaust Waterlock (Top In - Top Out / 60mm Hose) The Centek 1500014 Vernalift waterlock features a 'Top In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaust..

(6)

353.27€ Ex Tax: 353.27€

Centek GRP Exhaust Waterlock (Side In - Top Out / 51mm Hose)

Centek GRP Exhaust Waterlock (Side In - Top Out / 51mm Hose) The Centek 1500027 Vernalift waterlock features a 'Side In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaust systems..

(4)

351.50€ Ex Tax: 351.50€

Centek GRP Exhaust Waterlock (Top In - Top Out / 51mm Hose)

Centek GRP Exhaust Waterlock (Top In - Top Out / 51mm Hose) The Centek 1500010 Vernalift waterlock features a 'Top In - Top Out' configuration. This waterlock is appropriate for use with inboard engines, sailboats and generators, but should be installed below the engine as the lowest point of the exhaust system. It can be installed above or below the waterline and is suitable for petrol (gas) or diesel applications. It has better sound absorbing properties of 22-28 dB depending on the engine it is being used with. The Centek range of exhaust waterlocks are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the waterlocks are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernalift is only suitable for use in wet exhaust systems a..

(13)

339.96€ Ex Tax: 339.96€

Centek Vernatone Round GRP Exhaust Muffler (76mm Hose)

Centek Vernatone Round GRP Exhaust Muffler (76mm Hose) The Centek 1000104 inline Vernatone Round muffler is suitable for all inboard engines. The Vernatone is suitable for use with petrol (gas) or diesel but must only be installed above the waterline. It has good sound absorbing properties of 15-18 dB depending on the engine it is being used with. The Centek range of exhaust mufflers are made from heat resistant GRP (glass reinforced plastic) along with the rest of their wet exhaust system components. Because of this construction, the mufflers are corrosion resistant and can withstand heat up to 177°C (350°F). The Centek exhaust range is ABS, ABYC, Lloyds and UL approved. The Centek Vernatone is only suitable for use in wet exhaust systems and should be used with approved rubber marine exhaust hose. Specifications Application Inboards O..

(7)

332.39€ Ex Tax: 332.39€

Horizontal Exhaust Muffler Vetus NLPH 90mm

Horizontal Exhaust Muffler Vetus NLPH 90mmHorizontal two chamber waterlock/muffler with rotatable components and hose connections. Simple and time-saving installation. Capacity: 40/45/50 3 liters - 60/75/90 10 liters...

(10)

319.35€ Ex Tax: 319.35€